Ford Explorer: Automatic Transmission - 10-Speed Automatic Transmission – 10R60 / Diagnosis and Testing - A Clutch

Ford Explorer 2020-2024 Service Manual / Powertrain / Automatic Transmission / Automatic Transmission - 10-Speed Automatic Transmission – 10R60 / Diagnosis and Testing - A Clutch

Symptom Chart

A Clutch

For A clutch operation,
REFER to: A Clutch (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Description and Operation).


  A Clutch


Condition Possible Sources Action
A clutch does not apply SSA mechanically stuck OFF INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
A clutch control valve stuck OFF DISASSEMBLE, CLEAN and INSPECT the A clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
A clutch latch valve stuck OFF DISASSEMBLE, CLEAN and INSPECT the A clutch latch valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
A clutch hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
CARRY OUT the air pressure test on the A clutch.
REFER to: Special Testing Procedures (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Diagnosis and Testing).
If a leak is detected, INSPECT the front support assembly and A clutch piston seals for leaks. INSTALL new components as necessary. REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
Front support assembly, ring gear no. 1 DISASSEMBLE and INSPECT the front support assembly hydraulic passages for debris, blockage or leaks. INSPECT the front support assembly and ring gear no. 1 for wear and damage. CLEAN or INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
A clutch piston seals DISASSEMBLE and INSPECT the A clutch piston seals for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
A clutch friction plates DISASSEMBLE and INSPECT the A clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
A clutch always applied SSA mechanically stuck ON INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
A clutch control valve stuck ON DISASSEMBLE, CLEAN and INSPECT the A clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
A clutch latch valve stuck ON DISASSEMBLE, CLEAN and INSPECT the A clutch latch valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
A clutch hydraulic circuit cross leaks DISASSEMBLE and INSPECT the main control valve body and separator plate passages for cracks, warping and damage. If damage is found, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
Front support assembly, ring gear no. 1 DISASSEMBLE and INSPECT the front support assembly hydraulic passages for debris, blockage and leaks. Inspect the front support assembly and ring gear no. 4 for wear and damage. CLEAN or INSTALL new components necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
A clutch piston return spring DISASSEMBLE and INSPECT the A clutch piston return spring for damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
A clutch friction plates DISASSEMBLE and INSPECT the A clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
A clutch delayed/soft/slipping apply Incorrect transmission strategy programmed into PCM/ TCM. CARRY OUT the Transmission Strategy Download and the Adaptive Learning Drive Cycle.
REFER to: Transmission Strategy Download (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, General Procedures).
REFER to: Adaptive Learning Drive Cycle (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, General Procedures).
Low line pressure CARRY OUT the line pressure test. If line pressure is low, REFER to the Line Pressure Diagnosis Chart.
REFER to: Special Testing Procedures (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Diagnosis and Testing).
SSA mechanically sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, INSTALL a new solenoid.
    REFER to: Shift Solenoids (SS) (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
A clutch control valve sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, DISASSEMBLE, CLEAN and INSPECT the A clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
    REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
A clutch latch valve sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, DISASSEMBLE, CLEAN and INSPECT the A clutch latch valve. If the bore or valve is damaged, INSTALL a new main control valve body.
    REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
A clutch hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
CARRY OUT the air pressure test on the A clutch.
REFER to: Special Testing Procedures (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Diagnosis and Testing).
If a leak is detected, INSPECT the front support assembly and A clutch piston seals for leaks. INSTALL new components as necessary. REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
A clutch piston seals DISASSEMBLE and INSPECT the A clutch piston seals for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
A clutch friction plates DISASSEMBLE and INSPECT the A clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
A clutch harsh apply Incorrect transmission strategy programmed into PCM/ TCM. CARRY OUT the Transmission Strategy Download and the Adaptive Learning Drive Cycle.,
REFER to: Transmission Strategy Download (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, General Procedures).
REFER to: Adaptive Learning Drive Cycle (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, General Procedures).
High line pressure CARRY OUT the line pressure test. If line pressure is high, REFER to the Line Pressure Diagnosis Chart.
REFER to: Special Testing Procedures (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Diagnosis and Testing).
SSA mechanically sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, INSTALL a new solenoid.
    REFER to: Shift Solenoids (SS) (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Removal and Installation).
A clutch control valve sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, DISASSEMBLE, CLEAN and INSPECT the A clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
    REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
A clutch latch valve sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, DISASSEMBLE, CLEAN and INSPECT the A clutch latch valve. If the bore or valve is damaged, INSTALL a new main control valve body.
    REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
A clutch hydraulic circuit blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
A clutch piston return spring DISASSEMBLE and INSPECT the A clutch piston return spring for damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
A clutch friction plates DISASSEMBLE and INSPECT the A clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).

    Diagnosis and Testing - Special Testing Procedures

    Line Pressure Test This test verifies the line pressure is within specification. If available, refer to the Transmission Line Pressure Test general procedure to access the line pressure ..

    Diagnosis and Testing - B Clutch

    Symptom Chart B Clutch For B clutch operation, REFER to: B Clutch (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Description and Operation)...

    Other information:

    Ford Explorer 2020-2024 Service Manual: Specifications


      General Specifications Item Specification Plug Weld hole 8 mm (0.315 in) Weld Wire ER70S-3 0.9 mm (0.0354 in) - 1.1 mm (0.0433 in) Weld Wire ER70S-6 0...

    Ford Explorer 2020-2024 Service Manual: Removal and Installation - Front Door Side Impact Sensor


    Removal   WARNING: The following procedure prescribes critical repair steps required for correct restraint system operation during a crash. Follow all notes and steps carefully. Failure to follow step instructions may result in incorrect operation of the restraint system and increases the risk of serious personal injury or death in a crash...

    лучшее казино онлайн России

    Categories

    Locking and Unlocking

    You can use the power door lock control or the remote control to lock and unlock your vehicle.

    Power Door Locks

    The power door lock control is on the driver and front passenger door panels.

    read more

     
    Copyright © 2024 www.foexplorer.com