Ford Explorer: Automatic Transmission - 10-Speed Automatic Transmission – 10R60 / Diagnosis and Testing - D Clutch

Ford Explorer 2020-2024 Service Manual / Powertrain / Automatic Transmission / Automatic Transmission - 10-Speed Automatic Transmission – 10R60 / Diagnosis and Testing - D Clutch

Symptom Chart

D Clutch

For D clutch operation,
REFER to: D Clutch (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Description and Operation).


  D Clutch


Condition Possible Sources Action
D clutch does not apply SSD mechanically stuck OFF INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
D clutch control valve stuck OFF DISASSEMBLE, CLEAN and INSPECT the D clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
D clutch hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
If a leak is detected, INSPECT the front support assembly, input shaft Teflon seals and D clutch piston seals for leaks. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
CDF clutch cylinder, planetary carrier no. 3 DISASSEMBLE and INSPECT the CDF clutch cylinder and planetary carrier no. 3 for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch piston seals DISASSEMBLE and INSPECT the D clutch piston seals for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch friction plates DISASSEMBLE and INSPECT the D clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch always applied SSD mechanically stuck ON INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
D clutch control valve stuck ON DISASSEMBLE, CLEAN and INSPECT the D clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
D clutch hydraulic circuit cross leaks DISASSEMBLE and INSPECT the main control valve body and separator plate passages for cracks, warping and damage. If damage is found, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
CDF clutch cylinder, planetary carrier no. 3 DISASSEMBLE and INSPECT the components for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch piston return spring DISASSEMBLE and INSPECT the D clutch piston return spring for damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch friction plates DISASSEMBLE and INSPECT the D clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch delayed/soft/slipping apply Incorrect transmission strategy programmed into PCM/ TCM. CARRY OUT the Transmission Strategy Download and the Adaptive Learning Drive Cycle.
REFER to: Transmission Strategy Download (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, General Procedures).
REFER to: Adaptive Learning Drive Cycle (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, General Procedures).
Low line pressure CARRY OUT the line pressure test. If line pressure is low, REFER to the Line Pressure Diagnosis Chart.
REFER to: Special Testing Procedures (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Diagnosis and Testing).
SSD mechanically sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, INSTALL a new solenoid.
    REFER to: Shift Solenoids (SS) (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
D Clutch control valve sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, DISASSEMBLE, CLEAN and INSPECT the D clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
    REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
D clutch hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
CARRY OUT the air pressure test on the D clutch.
REFER to: Special Testing Procedures (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Diagnosis and Testing).
If a leak is detected, INSPECT the front support assembly, input shaft Teflon seals and D clutch piston seals for leaks. INSTALL new components as necessary. REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch piston seals DISASSEMBLE and INSPECT the D clutch piston seals for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch friction plates DISASSEMBLE and INSPECT the D clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch harsh apply Incorrect transmission strategy programmed into PCM/ TCM. CARRY OUT the Transmission Strategy Download and the Adaptive Learning Drive Cycle.
REFER to: Transmission Strategy Download (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, General Procedures).
REFER to: Adaptive Learning Drive Cycle (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, General Procedures).
High line pressure CARRY OUT the line pressure test. If line pressure is high, REFER to the Line Pressure Diagnosis Chart.
REFER to: Special Testing Procedures (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Diagnosis and Testing).
SSD mechanically sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, INSTALL a new solenoid.
    REFER to: Shift Solenoids (SS) (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
D clutch control valve sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, DISASSEMBLE, CLEAN and INSPECT the D clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
    REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
D clutch hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
D clutch piston return spring DISASSEMBLE and INSPECT the D clutch piston return spring for damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).
D clutch friction plates DISASSEMBLE and INSPECT the D clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80, Overhaul).

    Diagnosis and Testing - C Clutch

    Symptom Chart C Clutch For C clutch operation, REFER to: C Clutch (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Description and Operation)...

    Diagnosis and Testing - E Clutch

    Symptom Chart E Clutch For E clutch operation, REFER to: E Clutch (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Description and Operation)...

    Other information:

    Ford Explorer 2020-2024 Service Manual: Description and Operation - Low One-Way Clutch Assembly


    One-Way Clutch (OWC) Exploded View Item Description 1 Front support assembly 2 One-Way Clutch (OWC) 3 Sun gear No. 1 4 Sun gear No. 2 One-Way Clutch (OWC) Mechanical Operation The One-Way Clutch (OWC) is a brake clutch that holds the sun gears No...

    Ford Explorer 2020-2024 Service Manual: General Procedures - Driveshaft Angle Measurement


    Check NOTE: Prior to checking driveline angularity, inspect the U-joints for correct operation. NOTE: An incorrect driveline angle can cause a vibration or shudder. NOTE: Driveline angularity is the angular relationship between the engine crankshaft, the driveshaft and the rear axle pinion...

    топ казино на деньги

    Categories

    Child Safety Locks

    When these locks are set, you cannot open the rear doors from the inside.

    A child safety lock is on the rear edge of each rear door. You must set the child safety lock separately on each door.

    Left-Hand Side

    read more

     
    Copyright © 2024 www.foexplorer.com