Ford Explorer: Automatic Transmission - 10-Speed Automatic Transmission – 10R60 / Removal and Installation - Transmission Fluid Auxiliary Pump
Removal
-
NOTE: It is not necessary to remove the transmission fluid filter to remove the transmission fluid auxiliary pump.
Remove the transmission fluid pan and gasket.
Refer to: Transmission Fluid Pan, Gasket and Filter (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
-
Remove the bolt and the transmission fluid auxiliary pump tube.
.jpg) |
-
Remove the transmission fluid auxiliary pump tube seal.
.jpg) |
-
Disconnect the transmission fluid auxiliary pump.
.jpg) |
-
NOTE: A short 1/4" drive T-30 socket is required to remove the rear pump bolt.
NOTE: The fluid auxiliary pump may need to be removed from the RH side of the vehicle to clear the exhaust system and fluid filter.
Remove the bolts and the transmission fluid auxiliary pump.
-
If necessary, remove the fluid auxiliary pump towards the RH side.
-
If necessary, remove the fluid auxiliary pump towards the RH side.
.jpg) |
Installation
-
Install the transmission fluid auxiliary pump and loosely install the bolts.
.jpg) |
-
Install the transmission fluid auxiliary pump tube seal.
.jpg) |
-
Inspect the transmission fluid auxiliary pump tube O-ring.
.jpg) |
-
Install the transmission fluid auxiliary pump tube and loosely install the bolt.
.jpg) |
-
-
Transmission fluid auxiliary pump bolts
Torque: 97 lb.in (11 Nm)
-
Transmission fluid auxiliary pump tube bolt
Torque: 106 lb.in (12 Nm)
-
Transmission fluid auxiliary pump bolts
.jpg) |
-
Connect the transmission fluid auxiliary pump electrical connector.
.jpg) |
-
Install the transmission fluid pan and gasket.
Refer to: Transmission Fluid Pan, Gasket and Filter (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
Removal and Installation - Transmission - 3.3L Duratec-V6
Special Tool(s) /
General Equipment
307-346
(T97T-7902-A)
Retainer, Torque ConverterTKIT-1998-LM (NavigatoR)TKIT-1997-F/FLM/LT
Magnetic Socket
Transmission Jack
Wooden Block
..
Removal and Installation - Transmission Fluid Pan, Gasket and Filter
Materials
Name
Specification
Motorcraft® MERCON® ULV Automatic Transmission FluidXT-12-QULV
WSS-M2C949-A, MERCON® ULV
Removal
With the vehicle in NEUTRAL, positi..
Other information:
Ford Explorer 2020-2025 Service Manual: Removal and Installation - Audio Controls
Special Tool(s) / General Equipment Interior Trim Remover Removal NOTE: Removal steps in this procedure may contain installation details. All vehicles Remove the upper instrument trim panel. Remove the screws. Torque: 22 lb...
Ford Explorer 2020-2025 Service Manual: Removal and Installation - Rear Climate Control Housing
Removal NOTICE: During the removal or installation of components, cap, tape or otherwise appropriately protect all openings and tubes/fittings to prevent the ingress of dirt or other contamination. Remove caps, tape and other protective materials prior to installation...
Categories
- Manuals Home
- 6th Generation Explorer Owners Manual
- 6th Generation Explorer Service Manual
- General Procedures - Brake Service Mode Activation and Deactivation
- General Procedures - Rear Camber Adjustment
- Using Tether Straps
- New on site
- Most important about car
Driver and Passenger Airbags
WARNING: Do not place your arms on the airbag cover or through the steering wheel. Failure to follow this instruction could result in personal injury.
WARNING: Keep the areas in front of the airbags free from obstruction. Do not affix anything to or over the airbag covers. Objects could become projectiles during airbag deployment or in a sudden stop. Failure to follow this instruction could result in personal injury or death.
WARNING: Airbags can kill or injure a child in a child restraint. Never place a rear-facing child restraint in front of an active airbag. If you must use a forward-facing child restraint in the front seat, move the seat upon which the child restraint is installed all the way back.
