Ford Explorer: Exterior Lighting / Diagnosis and Testing - Parking, Rear and License Plate Lamps

Ford Explorer 2020-2024 Service Manual / Electrical / Lighting / Exterior Lighting / Diagnosis and Testing - Parking, Rear and License Plate Lamps

Diagnostic Trouble Code (DTC) Chart

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).

Diagnostic Trouble Code Chart

Module	DTC	Description	Action
BCM	B10F3:11	Left Front Position Light: Circuit Short to Ground	GO to Pinpoint Test A
BCM	B10F3:15	Left Front Position Light: Circuit Short to Battery or Open	GO to Pinpoint Test A
BCM	B10F4:11	Right Front Position Light: Circuit Short to Ground	GO to Pinpoint Test A
BCM	B10F4:15	Right Front Position Light: Circuit Short to Battery or Open	GO to Pinpoint Test A
BCM	B1445:11	Rear Park Lamps Output: Circuit Short to Ground	GO to Pinpoint Test A
BCM	B1445:15	Rear Park Lamps Output: Circuit Short to Battery or Open	GO to Pinpoint Test A
BCM	B1447:11	Parklamp On Switch Input: Circuit Short to Ground	REFER to: Headlamps (417-01 Exterior Lighting, Diagnosis and Testing).
BCM	B149E:11	Left Front Position/Sidemarker: Circuit Short To Ground	GO to Pinpoint Test A
BCM	B149E:15	Left Front Position/Sidemarker: Circuit Short To Battery or Open	GO to Pinpoint Test A
BCM	B149F:11	Right Front Position/Sidemarker: Circuit Short To Ground	GO to Pinpoint Test A
BCM	B149F:15	Right Front Position/Sidemarker: Circuit Short To Battery or Open	GO to Pinpoint Test A
BCM	B14A2:11	Tailgate/Liftgate Applique Lamps:Circuit Short To Ground	GO to Pinpoint Test A
BCM	B14A2:15	Tailgate/Liftgate Applique Lamps: Circuit Short To Battery or Open	GO to Pinpoint Test A
BCM	B14B2:11	Left Position Lamps: Circuit Short To Ground	GO to Pinpoint Test A
BCM	B14B2:15	Left Position Lamps: Circuit Short To Battery or Open	GO to Pinpoint Test A
BCM	B14B3:11	Right Position Lamps: Circuit Short To Ground	GO to Pinpoint Test A
BCM	B14B3:15	Right Position Lamps: Circuit Short To Battery or Open	GO to Pinpoint Test A
For other BCM Diagnostic Trouble Codes (DTCs)	-	-	REFER to: Body Control Module (BCM) (419-10 Multifunction Electronic Modules, Diagnosis and Testing).

игровой клуб

Symptom Charts

Symptom Chart: Parking, Rear and License Plate Lamps

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).

Condition	Possible Sources	Actions
A module does not respond to the diagnostic scan tool	Fuse Wiring, terminals or connectors Module	REFER to: Communications Network (418-00 Module Communications Network, Diagnosis and Testing).
One or more parking, signature, rear or license plate lamps are inoperative or always on	Refer to the Pinpoint Test	GO to Pinpoint Test A
One or more front LED daytime running lamp/front parking lamp is inoperative or does not dim if DRL are active - mid and high series headlamps only	Refer to the Pinpoint Test	GO to Pinpoint Test A

Pinpoint Tests

PINPOINT TEST A : ONE OR MORE PARKING, SIGNATURE, REAR OR LICENSE PLATE LAMPS ARE INOPERATIVE OR ALWAYS ON

Refer to Wiring Diagrams Cell 92 for schematic and connector information.

Normal Operation and Fault Conditions

REFER to: Exterior Lighting - Overview (417-01 Exterior Lighting, Description and Operation).
REFER to: Exterior Lighting - System Operation and Component Description (417-01 Exterior Lighting, Description and Operation).

DTC Fault Trigger Conditions

DTC	Description	Fault Trigger Condition
BCM B10F3:11	Left front position light: Circuit Short To Ground	A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the LH front parking lamps output circuit.
BCM B10F3:15	Left front position light: Circuit Short To Battery Or Open	A continuous memory and on-demand DTC that sets when the BCM detects an open or short to voltage from the LH front parking lamps output circuit.
BCM B10F4:11	Right front position light: Circuit Short To Ground	A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the RH front parking lamps output circuit.
BCM B10F4:15	Right front position light: Circuit Short To Battery Or Open	A continuous memory and on-demand DTC that sets when the BCM detects an open or short to voltage from the RH front parking lamps output circuit.
BCM B1445:11	Rear Park Lamps Output: Circuit Short To Ground	A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the license plate lamps output circuit.
BCM B1445:15	Rear Park Lamps Output: Circuit Short To Battery Or Open	A continuous memory and on-demand DTC that sets when the BCM detects an open or short to voltage from the license plate lamps output circuit.
BCM B149E:11	Left Front Position/Sidemarker: Circuit Short To Ground	A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the LH front parking lamps output circuit.
BCM B149E:15	Left Front Position/Sidemarker: Circuit Short To Battery Or Open	A continuous memory and on-demand DTC that sets when the BCM detects an open or short to voltage from the LH front parking lamps output circuit.
BCM B149F:11	Right Front Position/Sidemarker: Circuit Short To Ground	A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the RH front parking lamps output circuit.
BCM B149F:15	Right Front Position/Sidemarker: Circuit Short To Battery Or Open	A continuous memory and on-demand DTC that sets when the BCM detects an open or short to voltage from the RH front parking lamps output circuit.
BCM B14A2:11	Tailgate/Liftgate Applique Lamps: Circuit Short To Ground	A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the license plate lamps output circuit.
BCM B14A2:15	Tailgate/Liftgate Applique Lamps: Circuit Short To Battery Or Open	A continuous memory and on-demand DTC that sets when the BCM detects an open or short to voltage from the license plate lamps output circuit.
BCM B14B2:11	Left Position Lamps: Circuit Short To Ground	A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the LH front parking lamps output circuit.
BCM B14B2:15	Left Position Lamps: Circuit Short To Battery Or Open	A continuous memory and on-demand DTC that sets when the BCM detects an open or short to voltage from the LH front parking lamps output circuit.
BCM B14B3:11	Right Position Lamps: Circuit Short To Ground	A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the RH front parking lamps output circuit.
BCM B14B3:15	Right Position Lamps: Circuit Short To Battery Or Open	A continuous memory and on-demand DTC that sets when the BCM detects an open or short to voltage from the RH front parking lamps output circuit.

Possible Sources

Wiring, terminals or connectors
Headlamp assembly
Rear lamp assembly
LED control module
BCM

A1 DETERMINE IF ALL THE PARKING LAMPS ARE INOPERATIVE

Ignition ON.

Place the headlamp switch in the PARKING LAMPS position and observe all the parking lamps.

Place the headlamp switch in the OFF position and observe all the parking lamps.

Are any of the parking lamps always on?

Yes

If one or more of the parking lamps are always on, GO to A2
If all the parking lamps are always on, GO to A24

If the signature or LED DRL/front parking lamp is inoperative, GO to A3
If the front side marker lamp (if equipped) is inoperative, GO to A8
If both license plate lamps only are inoperative, GO to A14
If one license plate lamps are inoperative, VERIFY the license plate bulb(s) are OK. INSTALL new bulb(s) if necessary. If the bulb(s) are OK, REPAIR the liftgate moulding wiring harness. If the harness can not be repaired, INSTALL a new liftgate moulding.
REFER to: Liftgate Moulding (501-08 Exterior Trim and Ornamentation, Removal and Installation). If one of the rear parking lamps is inoperative, GO to A19
If all parking lamps are inoperative, GO to A24

A2 CHECK THE BCM (BODY CONTROL MODULE) PARKING LAMP OUTPUT CIRCUIT FOR A SHORT TO VOLTAGE

Ignition OFF.

Disconnect: BCM C2280F (For front parking, rear parking and side marker lamps).

Disconnect: BCM C2280C (For license plate lamps).

Ignition ON.

Do the parking lamps continue to illuminate?

Yes

REPAIR the affected circuit.

GO to A24

A3 CHECK FOR VOLTAGE TO THE FRONT SIGNATURE AND LED (LIGHT EMITTING DIODE) DRL (DAYTIME RUNNING LAMPS) /FRONT PARKING LAMP

Place the headlamp switch in the OFF position.

Ignition OFF.

Disconnect: Inoperative LH Headlamp C1284 or RH Headlamp C1285.

Ignition ON.

Place the headlamp switch in the PARKING LAMPS position.

Measure:
Click to display connectors
LH front signature and LED DRL/front parking lamp

Positive Lead Measurement / Action Negative Lead

C1284-4 Ground

Click to display connectors
RH front signature and LED DRL/front parking lamp

Positive Lead Measurement / Action Negative Lead

C1285-4 Ground

Is the voltage approximately 2 volts?

Yes

GO to A5

GO to A4

A4 REPEAT THE ON-DEMAND SELF-TEST AND CHECK FOR VOLTAGE TO THE FRONT SIGNATURE AND LED (LIGHT EMITTING DIODE) DRL (DAYTIME RUNNING LAMPS) /FRONT PARKING LAMP

Place the headlamp switch in the OFF position.

Using a diagnostic scan tool, perform the BCM self-test.

Clear the Diagnostic Trouble Codes (DTCs) and repeat the self-test (required to enable the lamp output driver).

Ignition OFF.

Ignition ON.

Place the headlamp switch in the PARKING LAMPS position.

Measure:
Click to display connectors
LH front signature and LED DRL/front parking lamp

Positive Lead Measurement / Action Negative Lead

C1284-4 Ground

Click to display connectors
RH front signature and LED DRL/front parking lamp

Positive Lead Measurement / Action Negative Lead

C1285-4 Ground

Is the voltage approximately 2 volts?

Yes

GO to A13

GO to A6

A5 CHECK THE FRONT SIGNATURE AND LED (LIGHT EMITTING DIODE) DRL (DAYTIME RUNNING LAMPS) /FRONT PARKING LAMP GROUND CIRCUIT FOR AN OPEN

Measure:
Click to display connectors
LH front signature and LED DRL/front parking lamp

Positive Lead Measurement / Action Negative Lead

C1284-4 C1284-8

Click to display connectors
RH front signature and LED DRL/front parking lamp

Positive Lead Measurement / Action Negative Lead

C1285-4 C1285-8

Is the voltage approximately 2 volts?

Yes

GO to A13

No	REPAIR the circuit in question.

A6 CHECK THE FRONT SIGNATURE AND LED (LIGHT EMITTING DIODE) DRL (DAYTIME RUNNING LAMPS) /FRONT PARKING LAMP SUPPLY CIRCUIT FOR AN OPEN

Place the headlamp switch in the OFF position.

Ignition OFF.

Disconnect: BCM C2280F.

Measure:
Click to display connectors
LH front signature and LED DRL/front parking lamp

Positive Lead Measurement / Action Negative Lead

C1284-4 C2280F-40

Click to display connectors
RH front signature and LED DRL/front parking lamp

Positive Lead Measurement / Action Negative Lead

C1285-4 C2280F-36

Is the resistance less than 3 ohms?

Yes

GO to A7

No	REPAIR the circuit.

A7 CHECK THE FRONT SIGNATURE AND LED (LIGHT EMITTING DIODE) DRL (DAYTIME RUNNING LAMPS) /FRONT PARKING LAMP SUPPLY CIRCUIT FOR A SHORT TO GROUND

Measure:
Click to display connectors
LH front signature and LED DRL/front parking lamp

Positive Lead Measurement / Action Negative Lead

C1284-4 Ground

Click to display connectors
RH front signature and LED DRL/front parking lamp

Positive Lead Measurement / Action Negative Lead

C1285-4 Ground

Is the resistance greater than 10,000 ohms?

Yes

GO to A24

REPAIR the circuit. After the repair:
If no Diagnostic Trouble Codes (DTCs) are present, TEST the system for normal operation.
If DTC U1000:00 is present, CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test (required to enable the lamp output driver if DTC U1000:00 is present).
If DTC U3000:49 is present, INSTALL a new BCM.
REFER to: Body Control Module (BCM) (419-10 Multifunction Electronic Modules, Diagnosis and Testing).

A8 CHECK FOR VOLTAGE TO THE FRONT SIDE MARKER LAMP

Place the headlamp switch in the OFF position.

Ignition OFF.

Disconnect: Inoperative LH Headlamp C1284 or RH Headlamp C1285.

Ignition ON.

Place the headlamp switch in the PARKING LAMPS position.

Measure:
Click to display connectors
LH Front Side Marker Lamp

Positive Lead Measurement / Action Negative Lead

C1284-5 Ground

Click to display connectors
RH Front Side Marker Lamp

Positive Lead Measurement / Action Negative Lead

C1285-5 Ground

Is the voltage greater than 11 volts?

Yes

GO to A10

GO to A9

A9 REPEAT THE ON-DEMAND SELF-TEST AND CHECK FOR VOLTAGE TO THE FRONT SIDE MARKER LAMP

Place the headlamp switch in the OFF position.

Using a diagnostic scan tool, perform the BCM self-test.

Clear the Diagnostic Trouble Codes (DTCs) and repeat the self-test (required to enable the lamp output driver).

Ignition OFF.

Ignition ON.

Place the headlamp switch in the PARKING LAMPS position.

Measure:
Click to display connectors
LH Front Side Marker Lamp

Positive Lead Measurement / Action Negative Lead

C1284-5 Ground

Click to display connectors
RH Front Side Marker Lamp

Positive Lead Measurement / Action Negative Lead

C1285-5 Ground

Is the voltage greater than 11 volts?

Yes

GO to A13

GO to A11

A10 CHECK THE FRONT SIDE MARKER LAMP GROUND CIRCUIT FOR AN OPEN

Measure:
Click to display connectors
LH Front Side Marker Lamp

Positive Lead Measurement / Action Negative Lead

C1284-5 C1284-8

Click to display connectors
RH Front Side Marker Lamp

Positive Lead Measurement / Action Negative Lead

C1285-5 C1285-8

Does the voltage greater than 11 volts?

Yes

GO to A13

No	REPAIR the circuit in question.

A11 CHECK THE FRONT SIDE MARKER LAMP SUPPLY CIRCUIT FOR AN OPEN

Place the headlamp switch in the OFF position.

Ignition OFF.

Disconnect: BCM C2280F.

Measure:
Click to display connectors
LH Front Side Marker Lamp

Positive Lead Measurement / Action Negative Lead

C1284-5 C2280F-30

Click to display connectors
RH Front Side Marker Lamp

Positive Lead Measurement / Action Negative Lead

C1285-5 C2280F-37

Is the resistance less than 3 ohms?

Yes

GO to A12

No	REPAIR the circuit.

A12 CHECK THE FRONT SIDE MARKER LAMP SUPPLY CIRCUIT FOR A SHORT TO GROUND

Measure:
Click to display connectors
LH Front Side Marker Lamp

Positive Lead Measurement / Action Negative Lead

C1284-5 Ground

Click to display connectors
RH Front Side Marker Lamp

Positive Lead Measurement / Action Negative Lead

C1285-5 Ground

Is the resistance greater than 10,000 ohms?

Yes

GO to A24

A13 CHECK THE LED (LIGHT EMITTING DIODE) CONTROL MODULE

Place the headlamp switch in the OFF position.

Ignition OFF.

Connect: Inoperative LH Headlamp C1284 or RH Headlamp C1285.

Ignition ON.

CLEAR the Diagnostic Trouble Codes (DTCs), REPEAT the self-test (required to enable the lamp output driver) and cycle the ignition OFF and ON. REPEAT the self-test.

Activate the hazard flasher lamp function.

Operate the system and determine if the concern is still present.

Is the concern still present or does any Diagnostic Trouble Codes (DTCs) return?

Yes

REMOVE the known good LED control module. INSTALL a new headlamp assembly.
REFER to: Headlamp Assembly (417-01 Exterior Lighting, Removal and Installation).

No	REMOVE the known good LED control module. INSTALL a new LED control module. REFER to: Light Emitting Diode (LED) Control Module (417-01 Exterior Lighting, Removal and Installation).

A14 CHECK FOR VOLTAGE TO THE LICENSE PLATE LAMP

Place the headlamp switch in the OFF position.

Ignition OFF.

Disconnect: For vehicles with rear only parking aid camera, Liftgate Applique C4488.

Disconnect: For vehicles equipped with 360 degree camera, Liftgate Applique C4352.

Ignition ON.

Place the headlamp switch in the PARKING LAMPS position.

Measure:
Click to display connectors
Vehicles With Rear Only Parking Aid Camera

Positive Lead Measurement / Action Negative Lead

C4488-7 Ground

Click to display connectors
Vehicles Equipped With 360 Degree Camera

Positive Lead Measurement / Action Negative Lead

C4352-3 Ground

Is the voltage greater than 11 volts?

Yes

GO to A16

GO to A15

A15 REPEAT THE ON-DEMAND SELF-TEST AND CHECK FOR VOLTAGE TO THE LICENSE PLATE LAMP

Place the headlamp switch in the OFF position.

Using a diagnostic scan tool, perform the BCM self-test.

Clear the Diagnostic Trouble Codes (DTCs) and repeat the self-test (required to enable the lamp output driver).

Ignition OFF.

Ignition ON.

Place the headlamp switch in the PARKING LAMPS position.

Measure:
Click to display connectors
Vehicles With Rear Only Parking Aid Camera

Positive Lead Measurement / Action Negative Lead

C4488-7 Ground

Click to display connectors
Vehicles Equipped With 360 Degree Camera

Positive Lead Measurement / Action Negative Lead

C4352-3 Ground

Is the voltage greater than 11 volts?

Yes

REPAIR the liftgate moulding wiring harness. If the harness can not be repaired, INSTALL a new liftgate moulding.
REFER to: Liftgate Moulding (501-08 Exterior Trim and Ornamentation, Removal and Installation).

GO to A17

A16 CHECK THE LICENSE PLATE LAMP GROUND CIRCUIT FOR AN OPEN

Measure:
Click to display connectors
Vehicles With Rear Only Parking Aid Camera

Positive Lead Measurement / Action Negative Lead

C4488-7 C4488-10

Click to display connectors
Vehicles Equipped With 360 Degree Camera

Positive Lead Measurement / Action Negative Lead

C4352-3 C4352-2

Is the voltage greater than 11 volts?

Yes

No	REPAIR the circuit.

A17 CHECK THE LICENSE PLATE LAMP SUPPLY CIRCUIT FOR A SHORT TO GROUND

Place the headlamp switch in the OFF position.

Ignition OFF.

Disconnect: BCM C2280C.

Measure:
Click to display connectors

Positive Lead Measurement / Action Negative Lead

C2280C-12 Ground

Is the resistance greater than 10,000 ohms?

Yes

GO to A18

A18 CHECK THE LICENSE PLATE LAMP VOLTAGE SUPPLY CIRCUIT FOR AN OPEN

Measure:
Click to display connectors
Vehicles With Rear Only Parking Aid Camera

Positive Lead Measurement / Action Negative Lead

C4488-7 C2280C-12

Click to display connectors
Vehicles Equipped With 360 Degree Camera

Positive Lead Measurement / Action Negative Lead

C4352-3 C2280C-12

Is the resistance less than 3 ohms?

Yes

GO to A24

No	REPAIR the circuit.

A19 CHECK THE FOR VOLTAGE TO THE REAR PARKING LAMP

Place the headlamp switch in the OFF position.

Ignition OFF.

Disconnect: Inoperative LH Rear Lamp C414 or RH Rear Lamp C417.

Ignition ON.

Place the headlamp switch in the PARKING LAMPS position.

Measure:
Click to display connectors
LH Rear Parking Lamp

Positive Lead Measurement / Action Negative Lead

C414-3 Ground

Click to display connectors
RH Rear Parking Lamp

Positive Lead Measurement / Action Negative Lead

C417-3 Ground

Is the voltage greater than 11 volts?

Yes

GO to A21

GO to A20

A20 REPEAT THE ON-DEMAND SELF-TEST AND CHECK FOR VOLTAGE TO THE REAR PARKING LAMP

Place the headlamp switch in the OFF position.

Using a diagnostic scan tool, perform the BCM self-test.

Clear the Diagnostic Trouble Codes (DTCs) and repeat the self-test (required to enable the lamp output driver).

Ignition OFF.

Ignition ON.

Place the headlamp switch in the PARKING LAMPS position.

Measure:
Click to display connectors
LH Rear Parking Lamp

Positive Lead Measurement / Action Negative Lead

C414-3 Ground

Click to display connectors
RH Rear Parking Lamp

Positive Lead Measurement / Action Negative Lead

C417-3 Ground

Is the voltage greater than 11 volts?

Yes

INSTALL a new rear lamp assembly.
REFER to: Rear Lamp Assembly (417-01 Exterior Lighting, Removal and Installation).

GO to A22

A21 CHECK THE REAR PARKING LAMP GROUND CIRCUIT

Measure:
Click to display connectors
LH Rear Parking Lamp

Positive Lead Measurement / Action Negative Lead

C414-3 C414-1

Click to display connectors
RH Rear Parking Lamp

Positive Lead Measurement / Action Negative Lead

C417-3 C417-1

Is the voltage greater than 11 volts?

Yes

INSTALL a new rear lamp assembly.
REFER to: Rear Lamp Assembly (417-01 Exterior Lighting, Removal and Installation).

No	REPAIR the circuit in question.

A22 CHECK THE REAR PARKING LAMP SUPPLY CIRCUIT FOR AN OPEN

Place the headlamp switch in the OFF position.

Ignition OFF.

Disconnect: BCM C2280F.

Measure:
Click to display connectors
LH Rear Parking Lamp

Positive Lead Measurement / Action Negative Lead

C414-3 C2280F-30

Click to display connectors
RH Rear Parking Lamp

Positive Lead Measurement / Action Negative Lead

C417-3 C2280F-51

Is the resistance less than 3 ohms?

Yes

GO to A23

No	REPAIR the circuit in question.

A23 CHECK VOLTAGE CIRCUIT TO THE REAR PARKING LAMP FOR A SHORT TO GROUND

Measure:
Click to display connectors
LH Rear Parking Lamp

Positive Lead Measurement / Action Negative Lead

C414-3 Ground

Click to display connectors
RH Rear Parking Lamp

Positive Lead Measurement / Action Negative Lead

C417-3 Ground

Is the resistance greater than 10,000 ohms?

Yes

GO to A24

A24 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION

Disconnect and inspect all BCM connectors.

Repair:
- corrosion (install new connector or terminals – clean module pins)
- damaged or bent pins – install new terminals/pins
- pushed-out pins – install new pins as necessary

Reconnect the BCM connectors. Make sure they seat and latch correctly.

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes

CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new BCM.
REFER to: Body Control Module (BCM) (419-10 Multifunction Electronic Modules, Diagnosis and Testing).

No	The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

Diagnosis and Testing - Headlamps

Diagnostic Trouble Code (DTC) Chart Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Informati..

Diagnosis and Testing - Reversing Lamps

Other information:

Ford Explorer 2020-2024 Service Manual: Description and Operation - Blind Spot Information System - Overview

BLIS® The BLIS® aids the driver in assessing whether another vehicle is present within a specific area (blind spot) to either side of the vehicle, extending rearward approximately 6 m (20 ft) beyond the rear bumper while driving on roads and highways...

Ford Explorer 2020-2024 Owners Manual: Connecting the Vehicle to a Mobile Network

About the Modem The modem allows you to connect your vehicle to the Internet to use when you are on the road. If you enable the modem using the FordPass app, you can access the following services: Locating and remotely starting, locking and unlocking your vehicle...

Ford Explorer: Exterior Lighting / Diagnosis and Testing - Parking, Rear and License Plate Lamps

Diagnosis and Testing - Headlamps

Diagnosis and Testing - Reversing Lamps

Other information:

Ford Explorer 2020-2024 Service Manual: Description and Operation - Blind Spot Information System - Overview

Ford Explorer 2020-2024 Owners Manual: Connecting the Vehicle to a Mobile Network

Categories

Gauges